（内部）轴承座中心之间的光轴长度。 length of shaft between the centres of the （inner） bearing blocks
V形减速凸轮 V-shaped slowdown cam
标准光轴： Standard shafts：
表面粗糙度： Surface roughness：
表面硬度： Surface hardness：
不停机回转光轴上运行的驱动器。 drive operating on the rotating shaft without standstill
不圆度： Out-of-roundness：
材料卷绕速度 speed of the material to be wound
材料偏移范围 area of the material deflection
侧向推力 Side thrust
程序控制 Sequence control
齿形刻度盘 serrated scale
传动力矩 drive torque
从列线图确定寿命（小时） Determine the life from the nomogram （in hours）
粗糙度 roughness height rating
弹簧换向机构 spring-operated reversing mechanism.
电刷 Wipers
防腐蚀 corrosion protection
防锈防酸光轴： Rust- and acid-proof shafts：
防锈光轴： Rust-proof shafts：
分离支架 separate carriage
改变旋转方向 Changing direction of rotation
感应表面淬火surface-hardened by induction
感应淬火、研磨、抛光的钢轴。 induction-hardened， ground and finished steel shafts.
隔音 Noise dampening
光轴、导轨、轴承座和换向挡块 shaft， guide rails， bearing blocks and end stops
光轴材质 Shaft material
光轴速度 shaft speed
光轴下垂 shaft sag
光轴旋转 Shaft rotation
光轴直径 shaft diameter
滚动环动态能力 dynamic capacity of the rolling rings
滚动环径向载荷 radial load on the rolling rings
滚环驱动器产生的侧向推力 side thrust produced by the rolling ring drive
滚环驱动器在光轴自由移动用释放手柄 Release lever for free displacement of the rolling ring drive on the shaft
换向点加速度 acceleration at the reversal point
换向减速 Reversal slowdown.
换向减速滚动环驱动器 Rolling ring drives with reversal slowdown （feature V）
换向减速凸轮长度。 length of reversal slowdown cam
换向时间 reversal time
紧定螺钉 set screws
减速凸轮 slowdown cams
减速凸轮长度 Length of deceleration cam
节距设置 Pitch setting
锯齿形50级刻度盘 Serrated 50-step scale
卷绕线材张力 tension in the material to be wound
卷绕应用 Winding applications
卷筒盘接触来触发换向的移动键 Shifting linkage that makes contact with the spool flange to activate the reversal.
空转力矩 idling torque
控制手柄 control levers
连续调整节距用蜗轮驱动器 Worm gear drive for continuous adjustment of the pitch.
连续高速节距用坚定螺钉 Set screws for continuous adjustment of the pitch
联轴节连接。 Coupling connection
临界光轴速度 critical shaft speed
磨擦系数。 coefficient of friction
排线路径traversing path，
排线器行走方向张力 tension working against the direction of travel of the drive
排线速度的计算 Calculation of the traversing speed
配有光轴和轴承的滚环驱动器（ARG）。 Rolling ring drive （ARG）， complete with shaft and bearings
前端倒角 Leading end chamfer
切换机构 Switching mechanism
切换机构弹簧 springs in the snap-action switching mechanism
驱动电动机 Drive motor
驱动力矩 Drive torque
驱动器排线宽度 traversing width of the drive
全部研磨、精加工 All ground and superfinished
确定换向时间 To determine reversal time
绕线筒卷筒直径 barrel diameter of the bobbin
绕线筒与光轴最佳速度比 Optimum ratio between the bobbin and the shaft speeds
市场可购买到的不含MoS2滚柱轴承油脂 commercially available MoS2-free roller bearing greases
释放手柄 release lever
双动气缸 double-acting pneumatic cylinder
双轴承座 Double bearing support
瞬时换向、刻度盘、释放手柄 MCR features
瞬时换向滚动环驱动器 Rolling ring drives with instantaneous reversal
所需侧向推力 side thrust required
所需传动功率 drive power required
所选排线器最大节距 maximum pitch of the drive selected
停机旋转光轴上运行的驱动器。 drive operating on the rotating shaft with standstill
通过排线器箱体侧壁安装的滚轮防止扭转应变。 rotection against torsional strain by rollers mounted on the side wall of the housing.
同心度偏差 Concentricity tolerance
维护保养 Maintenance
无光轴和轴承的滚环驱动器 Rolling ring drive without shaft and bearings
无扭短联接适配器 Adapter for torque-free coupling
无需最小排线宽度 No minimum traversing width required.
线材最大卷绕直径或最大节距。 maximum diameter of the material to be wound or maximum pitch
载荷与支架总重的法向力。 normal force of the total weight of the payload and the carriage
支撑托架 Support bracket
直径公差： Diametral tolerance：
重型导轨 Heavy-duty guide rail
轴承座切削力分力 component of the cutting force of a separator）
轴驱动 Shaft drive
专用清漆 Special varnish
自锁钮 Self-locking knob
最大节距 maximum pitch
最低要求： Minimum requirements
最小换向距离： Minimum reversal distance
